Introduction: Automotive and telecom chambers test different products, but both depend on modular RF absorber cones to control reflections, stabilize fields, and make local maintenance practical.
A common planning conversation starts with the test object. One team is preparing a radar module, camera housing, or wiring harness; another is preparing a radio unit, baseband rack, or telecom power shelf. The objects look unrelated, yet each chamber has to do the same basic job: keep internal reflections from confusing the measurement. That shared job is why absorber cones appear in both rooms even when the room dimensions, antenna positions, and test standards differ. this guide maps those similarities and differences, then shows why a modular 5 x 5 cone panel such as the HZ-300 makes maintenance and layout changes easier to handle.
An anechoic chamber is not quiet because the room is empty. It is quiet because the walls, ceiling, and often the floor are lined with material that reduces reflections. In an automotive chamber, a radar sensor or ECU may be mounted on a fixture; in a telecom chamber, a rack-mounted transmitter or antenna may sit in the quiet zone. In both cases, the receiver or probe sees the direct signal plus any energy bounced from the chamber surfaces. Pyramidal absorber cones soften the transition from air to lossy foam, then dissipate part of the wave as it travels through the cone. IEC TR 61000-3-6 provides useful background on radiated immunity testing and uniform-field environments, which is the same reason both applications care about controlled reflections. The shared logic is easiest to see at the layout level. Both chambers need coverage on surfaces that can bounce energy toward the test object or the receiving antenna. Both benefit from absorber that is mechanically stable, because a sagging or damaged cone changes the local reflection pattern. Both also need access for fixtures, cables, turntables, and antennas. Transport-related EMC testing, reflected in FAA AC 8900.93, shows the same dependence on a controlled test environment rather than an untreated room. That is why different test objects still lead to a similar construction question: where should absorber be dense, where can it be uniform, and how can a damaged area be repaired without rebuilding the room? The answer usually involves modular panels rather than a single continuous liner.
The shared goal does not produce one universal layout. The test object, frequency interest, antenna position, and field-uniformity requirement change the practical arrangement. A chamber planned around a small radar sensor has different sight lines from a chamber planned around a telecom rack that may be moved between test campaigns. The absorber still controls reflections, but the useful placement of cones, the height mix, and the access zones can differ from room to room.
Automotive work often brings high-frequency radar modules, camera housings, ECUs, and wiring harnesses into the same test program. At millimeter-wave frequencies, small reflections matter because the wavelength is short and the antenna beam can be narrow. A cone panel near the radar face, a change in fixture height, or a reflective bracket can shift the local field pattern. Component tests may also need broadband coverage for emissions and immunity checks. The layout therefore tends to follow the antenna position and the mechanical package, with absorber placed to manage reflections around the device under test rather than only filling a full wall uniformly. The chamber still needs broad coverage, but local position matters more than a simple count of panels.
Telecom equipment tests often focus on rack-mounted radios, antennas, power supplies, and network hardware. The chamber may be used for emissions, immunity, or both, and repeatability becomes a daily concern because equipment changes and test configurations move. ITU K. 34 describes electromagnetic environmental conditions for telecommunication equipment, which helps explain why telecom teams care about a predictable field and a well-defined quiet zone. In practice, that pushes the absorber layout toward consistent wall and ceiling coverage, stable panel spacing, and clear access for racks and cabling. The goal is not just low reflection on one day, but a chamber condition that can be repeated when the next equipment sample arrives. That is a different emphasis from a radar-focused automotive test, even though both rooms rely on absorber cones.
A modular panel turns absorber from a wall-sized installation into a manageable unit. The HZ-300 from Haozhuo EMI Solutions is one concrete example: a 5 x 5 honeycomb pyramid cone array on a modular panel, with 300 mm total height, a 60 mm base, 240 mm cone height, 100 mm cone width, 9 kg panel weight, blue flexible foam, nominal 10 dB to 50 dB reflectivity, and CE/RoHS markings. The 5 x 5 array means 25 cones share one panel footprint, so the absorber has a repeatable building block rather than a loose collection of individual cones. That format suits chamber walls and ceilings where consistent spacing matters. Local maintenance is the practical benefit. If a cone is crushed, dusty, or damaged during fixture changes, the maintenance team can replace the affected panel instead of cutting out a large section of liner. A 9 kg panel is also easier to handle than a full wall section, which matters when work happens overhead or near sensitive equipment. The same modular logic supports layout changes: a new antenna position, a different test-object height, or a revised quiet zone can be handled by adjusting or adding panels in the affected area. That is the practical level at which an RF absorber manufacturer and an EMC absorber supplier usually discuss chamber upkeep: not just dB figures, but how a panel is handled, replaced, and fitted around fixtures. The panel is still one part of the chamber design, and the final layout should be checked against the chamber's intended tests.
For readers comparing absorber construction, the most useful takeaway is that the panel format is as important as the cone shape. Automotive chambers often put more emphasis on radar position and high-frequency reflections, while telecom chambers put more emphasis on stable fields and repeatable conditions. Both benefit from modular absorber arrays that can be replaced locally. The HZ-300 5 x 5 panel is a useful reference point for understanding that construction approach, especially when reviewing how a chamber layout might be maintained over time.
A: Modular absorber cones give both chamber types a practical way to control internal reflections. The cones reduce energy bounced from walls and ceiling, while the panel format allows consistent coverage and local replacement. Automotive and telecom tests differ, but both need a quiet RF environment for repeatable measurements.
A: No. Automotive radar and component tests often focus on high-frequency reflections, antenna position, and fixture geometry. Telecom EMC tests often emphasize stable fields and repeatable rack or antenna conditions. The absorber layout should follow the test object, frequency range, and chamber validation plan rather than copying a layout from another room.
A: A 5 x 5 panel groups 25 cones into one replaceable unit. If a small area is damaged or a layout change is needed, the team can swap or move that panel instead of rebuilding a large wall section. The 9 kg panel weight and defined dimensions make handling more predictable during overhead or local maintenance.
K.34 - Classification of electromagnetic environmental conditions for telecommunication equipment
300mm EMC Honeycomb RF Absorber Foam Liner Cones for Anechoic Chamber