Introduction: Custom EMC honeycomb absorber foam for a test chamber is specified from the chamber layout, working frequency, cone height, base footprint, counted module quantity, delivery target, and a drawing package that lets engineering confirm fit.
A complete chamber layout, cone height, base size, and counted module list turn a custom absorber inquiry into a quote a factory can build. You are fitting out an EMC test chamber for a communication or automotive electronics program, and the absorber lining sits inside a much larger construction plan. It still determines how quickly the RFQ moves because foam cones are priced from geometry, not from a catalog line. A request with a finished lining height, a base footprint, and a counted quantity per surface lets the factory price the work against your layout. A room outline with a short note asking for absorber foam usually produces a list of questions instead.
Chamber layout fixes absorber geometry before anyone chooses a product. Internal room dimensions define the surface area to be lined, ceiling height caps cone depth, and the positions of doors, vents, lights, and sprinkler heads determine where modules must be cut. Absorber depth also competes with working volume: a 300 mm lining on four walls and the ceiling removes 300 mm from each surface. In a chamber sized around a turntable, a test antenna, and the clearance your standard requires, that loss shapes the room.
The lowest frequency in your test plan sets the minimum cone height because a pyramid absorber works by transitioning gradually from open air into lossy material. Shorter cones still absorb well at higher frequencies and lose effectiveness as wavelength grows. HZ-300 shows the relationship in one product: a 300 mm build made of a 60 mm base plus 240 mm pyramids, arranged as a 5 x 5 array of 100 mm wide cones, with a stated reflectivity range of 10-50 dB across the marked bands. That makes 300 mm a practical middle ground for many communication and automotive electronics chambers, where wall space is limited and broadband attenuation still matters. Where your test plan reaches lower, a deeper lining earns its space; treat 300 mm as a reference point, not as a universal specification.
Almost every chamber has surfaces that a single module size cannot cover: door reveals, cable penetrations, ventilation openings, light fixtures, and the junction between wall and ceiling. Those edges are where custom work happens. A 5 x 5 array inside a square base gives a predictable grid, so a module cut at the perimeter can keep the cone pattern aligned with its neighbors and the lining reads as one continuous surface rather than a patchwork. Count modules from the elevation drawings instead of multiplying rough areas, and keep a spare allowance for edge cuts and later replacement of damaged cones. That counted list is what an EMC absorber supplier needs to price per module instead of guessing from square meters.
Start from the net internal dimensions of the shielded shell, not from the architectural room drawing made before shielding went in. For each surface, note the finished lined area, the cone height you want there, the module orientation, and every penetration with its size and position. Convert area into modules using the base footprint, then add your spare allowance. Weight follows the same count. At 9 kg per module on a 500 x 500 mm base, one square meter of lining carries roughly 36 kg before fixings, which is the figure your structural lead needs before the ceiling grid is fixed. Weight per square meter changes chamber designs more often than reflectivity does. Base size deserves its own line in the specification. HZ-300 references include 500 x 500 mm and 600 x 600 mm, and both require confirmation against the drawings for your chamber. The base grid decides how many modules fill a wall, how the perimeter cuts fall, and whether fixing points line up with the frame behind the lining. A flexible honeycomb foam structure helps here: the modules compress slightly and follow small irregularities in the shell, which is useful on retrofits and on walls that are not perfectly flat.
A request that moves straight into engineering carries a small, predictable package. Send plan and elevation drawings of the lined shell, a section showing cone height at each surface, a penetration schedule, the base footprint, module counts per surface with spares, your delivery target and destination port, and any documents your project file requires. PDF drawings are enough to start; DWG or STEP files shorten the review because they let the factory check the base grid against your frame. This is also the package an RF absorber manufacturer needs to return a buildable quote instead of a list of questions, and it keeps the conversation on geometry rather than guesswork. Commercial points are settled after that review. MOQ, sample schedule, and lead time are confirmed by engineering rather than assumed. The displayed USD 50 figure is a reference price, not a project quotation. CE and RoHS information is listed for the product; fire ratings are a separate matter and appear only where a specific rating is documented. If your chamber carries an OEM brand, trademark use in custom manufacturing follows the brand owner's authorization under the WIPO framework. Haozhuo EMI Solutions quotes HZ-300 and its 30 mm to 1000 mm series variants from drawings, ships from Shanghai Port, and reviews each request against the layout you send.
Custom absorber specifications are chamber decisions written down: cone height from your lowest test frequency, module footprint from your base grid, quantity from counted elevations, and weight from module count. Put those four onto one drawing set and the RFQ is based on your actual chamber rather than assumptions. Before you send it, check that the lining height is stated per surface, the base size is marked on the plan, spares are included, and your delivery target and document needs are written down. Send that package with your chamber layout for a geometry review, module count confirmation, and a quotation for the modules your chamber needs.
A: You need the net internal dimensions of the shielded room, the lined area and cone height for each surface, the base footprint you want, and the position and size of every door, vent, light, and cable penetration. Module counts per surface plus a spare allowance complete the picture.
A: Yes. The 300 mm build, with its 60 mm base and 240 mm pyramids, is one reference point in a series that runs from 30 mm to 1000 mm, and the base footprint is set against your drawings. References such as 500 x 500 mm and 600 x 600 mm exist, and both require confirmation for your chamber.
A: Include plan and elevation drawings, a section showing cone height at each surface, the base footprint, module counts with spares, delivery target and destination port, and required documents. Add your OEM branding needs if any. MOQ, sample timing, and lead time come back after engineering review.
CE marking - Internal Market, Industry, Entrepreneurship and SMEs
RoHS Directive - Environment - European Commission
300mm EMC Honeycomb RF Absorber Foam Liner Cones for Anechoic Chamber